K-1900-5
Hot-Line Touch
Tone Dialer
February 8, 2005
TECHNICAL
Practice
TELECOM SOLUTIONS FOR THE 21ST CENTURY
Replace Dedicated Phone Lines with a
Touch Tone Hot-Line Dialer
Why pay the premium of leased or dedicated phone lines?
The K-1900-5 will automatically dial a preprogrammed number,
of up to 32 digits, whenever an associated telephone is taken off
2
hook. Using non-volatile E memory, the K-1900-5 is telephone
line powered and will operate on any loop start central office line
or analog PABX/KSU extension.
The K-1900-5 is easily programmed remotely or locally using a
standard Touch Tone phone.
Applications
!
This product does not eliminate the
possibility of toll fraud! To further protect
against fraudulent calls, use with a TR-1
Toll Restrictor (Fax Back Document 705).
• Security and emergency phones
• Interactive point of sale displays
• Apartment security
• Catalog sales
Features
• Automated Teller Machines (ATM’s)
• Replaces leased ring down circuits
• Hot-Line reservation phones for hotels, airlines,
car rentals, etc.
• Touch Tone programmable
• Telephone line powered
2
• Non-volatile E memory (no batteries required)
• Ring detection (won’t dial on inbound calls)
• User programmable security code
• Programmable pauses in one and four second
increments
• Programmable to interrupt user Touch Tone
dialing to help control fraudulent calls from
hand held dialers, etc.
• Programmable dialing speed (normal or fast)
• Can be configured to operate from a contact
closure (Fax Back Document 818)
Specifications
Power: Telephone line powered (24V DC 20 mA minimum)*
Dimensions: 74mm x 53mm x 25mm (2.9” x 2.1” x 1.0”)
Shipping Weight: .45 kg (1 lb)
Environment: 0°C to 32°C (32°F to 90°F) with 5% to 95% non-
condensing humidity
Connections: (1) RJ11 plug, (1) RJ11 jack
Dialing Speed: Normal - 120ms on/off, Fast - 50ms on/off
* Note: When installing multiple line powered products (K-1900-5 and E-
10/E-15/E-20A/K-1500-EHF) on the same line, additional talk battery
voltage and loop current may be required.
Installation
A. Accessing the Programming Mode
Install the K-1900-5 in series between a telephone and a
C.O. line or analog PABX/KSU station.
1. Connect the K-1900-5 to a C.O. line or analog PABX/KSU station.
2. From a Touch Tone phone, call another phone connected to the
K-1900-5.
3. Take the phone connected to the dialer off hook (answer the
phone).
4. Enter ✱ followed by the six digit security code (see section D on
the next page). A double beep will indicate that you have
accessed the programming mode.
VIKING©
Programmable
Tone Dialer
Standard Analog
Telecom Device
C.O. Line or Analog
PABX/KSU Station
MODEL: K-1900-5
Quick Programming Guide
1. Call the phone connected to the dialer.
2. Answer phone. Enter ✱
&
security code.
(Factory set to 845464) Write your
security code below:
3. Enter your spped dial number
&
#00.
Note: For additional programming see
K-1900-5 Technical Practice.
Viking Electronics, Inc.
Hudson, WI 54016
5. You can now program your speed dial number and the following
features listed in section B below.
LINE IN
PHONE
Note: Programming from a cell-phone may not be suitable in areas
with weak coverage.
|
Toastmaster Juicer 1108 User Manual
Toshiba Computer Hardware L650 User Manual
TRENDnet Network Card TEW 641PC User Manual
TRENDnet Security Camera TVIP572W User Manual
Uniden Cell Phone TCX930 User Manual
ViewSonic Mouse KP102 User Manual
Volkswagen Motorized Toy Car W6202 User Manual
Vox Guitar HDC 77 User Manual
Walker Lawn Mower 36 User Manual
Weber Gas Grill 55009 User Manual